How to Increase R4 Card Wii Memory

by

Rebecca0813

With the latest firmware update to the Nintendo Wii, gamers are finally able to transfer and download WiiWare and Virtual Console games to be played directly from an SD R4 card. Using an SD card increases a Wii’s memory beyond what is available on the console, allowing for the download of more games, more channels and more fun.

Open the front flap on the Wii, between the eject and reset buttons. Push the SD card into the slot, with the label facing to the right if the Wii is standing upright, or with the label upright if the Wii is on its side. It should click into the slot.

Turn on the Wii and go to the Settings menu, accessible from the bottom left corner of the Wii Main Menu.

Open the Data Management Menu, then select “Channels.” Select the game or channel you want to transfer, select “Move,” then confirm you want to move the channel.

Go back to the Wii Main Menu and enter the SD card channel, accessible right next to the Wii Settings Menu icon. You can then select the game you wish to play, which will start up after a short load time.

Playing a Wii game and getting frustrated because your Wii Remote keeps losing the signal with the Wii console? Try increasing the range of your Wii Sensor Bar. The Wii Sensor Bar is a thin bar that sits above or below your TV and plugs into the back of the Wii game console. When you point your Wii Remote at the screen, the Sensor Bar uses two points of infrared light to determine the distance that the Wii remote is from the TV screen. Typically, Wii Remotes can be used 6 to 10 feet away from your TV.

Remove any sources of bright light near your Wii console. Bright lights interfere with the infrared signals that your Wii Remote is sending to the Sensor Bar. Besides bright lamps, remove burning candles, turn off space heaters, and shut off Christmas tree lights. Also, try closing blinds or curtains to block out bright sunlight.

Turn on your Wii. Click on the “Wii” button on the lower-left side of the Wii startup screen.

Click on the “Wii Settings” icon that looks like a wrench.

Click on the blue arrow on the right until you see the Wii System Settings 2 menu. Scroll down the menu and click on “Sensor Bar.”

Click “Sensitivity.” The Sensitivity option specifies how far the Sensor Bar can be from the Wii Remote and still work.

Hold the Wii Remote and move to where you are having problems with the Wii Remote losing contact with the game console.

Point the cursor at the screen and move the two white dots into the square test box on the screen. If you see two blinking dots in the square, your Sensor Bar is set correctly and should be working.

If you don’t see two blinking white dots, move the scroll bar under the test square to the right “+” side until you see the blinking dots.

Press “A” on the Wii remote to save the new Sensor Bar settings.

If you see more than two blinking dots in the test square, the Wii Remote is sensing other sources of light in the room. Walk around the room and eliminate light sources until you only see two dots on the screen.

Only move the Sensor Bar sensitivity to right until you see the blinking dots. Don’t automatically move to the highest sensitivity option. The higher sensitivity setting the greater chance that other types of light in the room will affect the Wii Remote.

Out of the box, the Nintendo Wii only comes with 512MB of internal memory. This is a decent amount of memory for game saves, but if you want to add additional content to your Wii (such as Wii Channels and downloadable content), you will need to get SD or SDHC R4 cards. These are small memory devices commonly used to increase the storage capacity of portable devices such as cameras or cell phones. The same can be done for the Nintendo Wii.

Dsicarte.com is The TOP 1

R4

store,we sell R4 Cards,you can buy Safe

R4 Cards

,Cheap nds R4 and

R4 Card

from us.

Article Source:

ArticleRich.com